(4) Insufficient antifreeze and too little coolant will also cause the water temperature to be too high, so it is necessary to add or replace the coolant in time. Due to the irregular addition and replacement of antifreeze, the engine water channel and water tank will be blocked in advance, resulting in excessive water temperature. Antifreeze should be replaced once every two years, and original fittings must be used when replacing and adding. If the concentration is too high, the heat dissipation effect will be poor and the engine will overheat. This harm is not obvious when the engine is running at low load, and the coolant temperature will be too high when it is running at high load and high speed. Therefore, it is not allowed to add antifreeze solution at will, and the concentration must be detected first. Different kinds of antifreeze cannot be mixed for use, so as not to cause chemical reaction, produce precipitation or bubbles, and reduce the use effect; When replacing antifreeze, start the engine first, then stop the engine and release the cleaning liquid. Add clean water to the cooling system, idle for 10 minute, then drain water, and repeat several times until clear water flows out of the waterway, and then add new antifreeze and water.
(5) There is air in the cooling system, which causes the cooling water not to circulate normally.
(6) The cylinder gasket is damaged, which causes the high temperature and high pressure gas in the cylinder to enter the cooling system, so that the water temperature quickly rises to boiling. A new cylinder liner must be replaced. The cylinder pads of the new two valves are made of steel plates. Generally, short-term high water temperature will not burn the cylinder gasket, but it will be damaged if it is not cooled for a long time. (3) The water pump is damaged or the transmission belt slips, resulting in poor water pump. The pump can't rotate normally to generate enough water pressure, which will also reduce the flow of cooling water. Because the circulating flow of cooling water exerts water pressure through the water pump, the water pressure cooled by the radiator enters the engine water jacket, forcing the cooling water that absorbs heat to flow to the radiator to dissipate heat. If the water pump does not work well, the water pressure is not high, the circulating flow of cooling water is reduced, and the heat dissipation effect is not obvious, resulting in high water temperature in the cooling system. The water pump is damaged, and the coolant can't be sent to the water tank, resulting in poor circulation of coolant and high water temperature until the pot is boiled. Need to repair or replace a new water pump. When replacing the timing belt, be sure to check the water pump for signs of leakage. If there is leakage, please replace it. Please carefully check one side of the timing belt for signs of water leakage. For vehicles with mileage exceeding1.2000 km, the owner is advised to replace the water pump when replacing the timing belt. For vehicles with long mileage, the shaft and blades are easy to separate, so we must pay attention to maintenance.
(4) Insufficient antifreeze and too little coolant will also cause the water temperature to be too high, so it is necessary to add or replace the coolant in time. Due to the irregular addition and replacement of antifreeze, the engine water channel and water tank will be blocked in advance, resulting in excessive water temperature. Antifreeze should be replaced once every two years, and original fittings must be used when replacing and adding. If the concentration is too high, the heat dissipation effect will be poor and the engine will overheat. This harm is not obvious when the engine is running at low load, and the coolant temperature will be too high when it is running at high load and high speed. Therefore, it is not allowed to add antifreeze solution at will, and the concentration must be detected first. Different kinds of antifreeze cannot be mixed for use, so as not to cause chemical reaction, produce precipitation or bubbles, and reduce the use effect; When replacing antifreeze, start the engine first, then stop the engine and release the cleaning liquid. Add clean water to the cooling system, idle for 10 minute, then drain water, and repeat several times until clear water flows out of the waterway, and then add new antifreeze and water.
(5) There is air in the cooling system, which causes the cooling water not to circulate normally.
(6) The cylinder gasket is damaged, which causes the high temperature and high pressure gas in the cylinder to enter the cooling system, so that the water temperature quickly rises to boiling. A new cylinder liner must be replaced. The cylinder pads of the new two valves are made of steel plates. Generally, short-term high water temperature will not burn the cylinder gasket, but it will be damaged if it is not cooled for a long time. (3) The water pump is damaged or the transmission belt slips, resulting in poor water pump. The pump can't rotate normally to generate enough water pressure, which will also reduce the flow of cooling water. Because the circulating flow of cooling water exerts water pressure through the water pump, the water pressure cooled by the radiator enters the engine water jacket, forcing the cooling water that absorbs heat to flow to the radiator to dissipate heat. If the water pump does not work well, the water pressure is not high, the circulating flow of cooling water is reduced, and the heat dissipation effect is not obvious, resulting in high water temperature in the cooling system. The water pump is damaged, and the coolant can't be sent to the water tank, resulting in poor circulation of coolant and high water temperature until the pot is boiled. Need to repair or replace a new water pump. When replacing the timing belt, be sure to check the water pump for signs of leakage. If there is leakage, please replace it. Please carefully check one side of the timing belt for signs of water leakage. For vehicles with mileage exceeding1.2000 km, the owner is advised to replace the water pump when replacing the timing belt. For vehicles with long mileage, the shaft and blades are easy to separate, so we must pay attention to maintenance.
(4) Insufficient antifreeze and too little coolant will also cause the water temperature to be too high, so it is necessary to add or replace the coolant in time. Due to the irregular addition and replacement of antifreeze, the engine water channel and water tank will be blocked in advance, resulting in excessive water temperature. Antifreeze should be replaced once every two years, and original fittings must be used when replacing and adding. If the concentration is too high, the heat dissipation effect will be poor and the engine will overheat. This harm is not obvious when the engine is running at low load, and the coolant temperature will be too high when it is running at high load and high speed. Therefore, it is not allowed to add antifreeze solution at will, and the concentration must be detected first. Different kinds of antifreeze cannot be mixed for use, so as not to cause chemical reaction, produce precipitation or bubbles, and reduce the use effect; When replacing antifreeze, start the engine first, then stop the engine and release the cleaning liquid. Add clean water to the cooling system, idle for 10 minute, then drain water, and repeat several times until clear water flows out of the waterway, and then add new antifreeze and water.
(5) There is air in the cooling system, which causes the cooling water not to circulate normally.
(6) The cylinder gasket is damaged, which causes the high temperature and high pressure gas in the cylinder to enter the cooling system, so that the water temperature quickly rises to boiling. A new cylinder liner must be replaced. The cylinder pads of the new two valves are made of steel plates. Generally, short-term high water temperature will not burn the cylinder gasket, but it will be damaged if it is not cooled for a long time. (3) The water pump is damaged or the transmission belt slips, resulting in poor water pump. The pump can't rotate normally to generate enough water pressure, which will also reduce the flow of cooling water. Because the circulating flow of cooling water exerts water pressure through the water pump, the water pressure cooled by the radiator enters the engine water jacket, forcing the cooling water that absorbs heat to flow to the radiator to dissipate heat. If the water pump does not work well, the water pressure is not high, the circulating flow of cooling water is reduced, and the heat dissipation effect is not obvious, resulting in high water temperature in the cooling system. The water pump is damaged, and the coolant can't be sent to the water tank, resulting in poor circulation of coolant and high water temperature until the pot is boiled. Need to repair or replace a new water pump. When replacing the timing belt, be sure to check the water pump for signs of leakage. If there is leakage, please replace it. Please carefully check one side of the timing belt for signs of water leakage. For vehicles with mileage exceeding1.2000 km, the owner is advised to replace the water pump when replacing the timing belt. For vehicles with long mileage, the shaft and blades are easy to separate, so we must pay attention to maintenance.
(4) Insufficient antifreeze and too little coolant will also cause the water temperature to be too high, so it is necessary to add or replace the coolant in time. Due to the irregular addition and replacement of antifreeze, the engine water channel and water tank will be blocked in advance, resulting in excessive water temperature. Antifreeze should be replaced once every two years, and original fittings must be used when replacing and adding. If the concentration is too high, the heat dissipation effect will be poor and the engine will overheat. This harm is not obvious when the engine is running at low load, and the coolant temperature will be too high when it is running at high load and high speed. Therefore, it is not allowed to add antifreeze solution at will, and the concentration must be detected first. Different kinds of antifreeze cannot be mixed for use, so as not to cause chemical reaction, produce precipitation or bubbles, and reduce the use effect; When replacing antifreeze, start the engine first, then stop the engine and release the cleaning liquid. Add clean water to the cooling system, idle for 10 minute, then drain water, and repeat several times until clear water flows out of the waterway, and then add new antifreeze and water.
(5) There is air in the cooling system, which causes the cooling water not to circulate normally.
(6) The cylinder gasket is damaged, which causes the high temperature and high pressure gas in the cylinder to enter the cooling system, so that the water temperature quickly rises to boiling. A new cylinder liner must be replaced. The cylinder pads of the new two valves are made of steel plates. Generally, short-term high water temperature will not burn the cylinder gasket, but it will be damaged if it is not cooled for a long time. (3) The water pump is damaged or the transmission belt slips, resulting in poor water pump. The pump can't rotate normally to generate enough water pressure, which will also reduce the flow of cooling water. Because the circulating flow of cooling water exerts water pressure through the water pump, the water pressure cooled by the radiator enters the engine water jacket, forcing the cooling water that absorbs heat to flow to the radiator to dissipate heat. If the water pump does not work well, the water pressure is not high, the circulating flow of cooling water is reduced, and the heat dissipation effect is not obvious, resulting in high water temperature in the cooling system. The water pump is damaged, and the coolant can't be sent to the water tank, resulting in poor circulation of coolant and high water temperature until the pot is boiled. Need to repair or replace a new water pump. When replacing the timing belt, be sure to check the water pump for signs of leakage. If there is leakage, please replace it. Please carefully check one side of the timing belt for signs of water leakage. For vehicles with mileage exceeding1.2000 km, the owner is advised to replace the water pump when replacing the timing belt. For vehicles with long mileage, the shaft and blades are easy to separate, so we must pay attention to maintenance.
(4) Insufficient antifreeze and too little coolant will also cause the water temperature to be too high, so it is necessary to add or replace the coolant in time. Due to the irregular addition and replacement of antifreeze, the engine water channel and water tank will be blocked in advance, resulting in excessive water temperature. Antifreeze should be replaced once every two years, and original fittings must be used when replacing and adding. If the concentration is too high, the heat dissipation effect will be poor and the engine will overheat. This harm is not obvious when the engine is running at low load, and the coolant temperature will be too high when it is running at high load and high speed. Therefore, it is not allowed to add antifreeze solution at will, and the concentration must be detected first. Different kinds of antifreeze cannot be mixed for use, so as not to cause chemical reaction, produce precipitation or bubbles, and reduce the use effect; When replacing antifreeze, start the engine first, then stop the engine and release the cleaning liquid. Add clean water to the cooling system, idle for 10 minute, then drain water, and repeat several times until clear water flows out of the waterway, and then add new antifreeze and water.
(5) There is air in the cooling system, which causes the cooling water not to circulate normally.
(6) The cylinder gasket is damaged, which causes the high temperature and high pressure gas in the cylinder to enter the cooling system, so that the water temperature quickly rises to boiling. A new cylinder liner must be replaced. The cylinder pads of the new two valves are made of steel plates. Generally, short-term high water temperature will not burn the cylinder gasket, but it will be damaged if it is not cooled for a long time. (3) The water pump is damaged or the transmission belt slips, resulting in poor water pump. The pump can't rotate normally to generate enough water pressure, which will also reduce the flow of cooling water. Because the circulating flow of cooling water exerts water pressure through the water pump, the water pressure cooled by the radiator enters the engine water jacket, forcing the cooling water that absorbs heat to flow to the radiator to dissipate heat. If the water pump does not work well, the water pressure is not high, the circulating flow of cooling water is reduced, and the heat dissipation effect is not obvious, resulting in high water temperature in the cooling system. The water pump is damaged, and the coolant can't be sent to the water tank, resulting in poor circulation of coolant and high water temperature until the pot is boiled. Need to repair or replace a new water pump. When replacing the timing belt, be sure to check the water pump for signs of leakage. If there is leakage, please replace it. Please carefully check one side of the timing belt for signs of water leakage. For vehicles with mileage exceeding1.2000 km, the owner is advised to replace the water pump when replacing the timing belt. For vehicles with long mileage, the shaft and blades are easy to separate, so we must pay attention to maintenance.
(4) Insufficient antifreeze and too little coolant will also cause the water temperature to be too high, so it is necessary to add or replace the coolant in time. Due to the irregular addition and replacement of antifreeze, the engine water channel and water tank will be blocked in advance, resulting in excessive water temperature. Antifreeze should be replaced once every two years, and original fittings must be used when replacing and adding. If the concentration is too high, the heat dissipation effect will be poor and the engine will overheat. This harm is not obvious when the engine is running at low load, and the coolant temperature will be too high when it is running at high load and high speed. Therefore, it is not allowed to add antifreeze solution at will, and the concentration must be detected first. Different kinds of antifreeze cannot be mixed for use, so as not to cause chemical reaction, produce precipitation or bubbles, and reduce the use effect; When replacing antifreeze, start the engine first, then stop the engine and release the cleaning liquid. Add clean water to the cooling system, idle for 10 minute, then drain water, and repeat several times until clear water flows out of the waterway, and then add new antifreeze and water.
(5) There is air in the cooling system, which causes the cooling water not to circulate normally.
(6) The cylinder gasket is damaged, which causes the high temperature and high pressure gas in the cylinder to enter the cooling system, so that the water temperature quickly rises to boiling. A new cylinder liner must be replaced. The cylinder pads of the new two valves are made of steel plates. Generally, short-term high water temperature will not burn the cylinder gasket, but it will be damaged if it is not cooled for a long time. (3) The water pump is damaged or the transmission belt slips, resulting in poor water pump. The pump can't rotate normally to generate enough water pressure, which will also reduce the flow of cooling water. Because the circulating flow of cooling water exerts water pressure through the water pump, the water pressure cooled by the radiator enters the engine water jacket, forcing the cooling water that absorbs heat to flow to the radiator to dissipate heat. If the water pump does not work well, the water pressure is not high, the circulating flow of cooling water is reduced, and the heat dissipation effect is not obvious, resulting in high water temperature in the cooling system. The water pump is damaged, and the coolant can't be sent to the water tank, resulting in poor circulation of coolant and high water temperature until the pot is boiled. Need to repair or replace a new water pump. When replacing the timing belt, be sure to check the water pump for signs of leakage. If there is leakage, please replace it. Please carefully check one side of the timing belt for signs of water leakage. For vehicles with mileage exceeding1.2000 km, the owner is advised to replace the water pump when replacing the timing belt. For vehicles with long mileage, the shaft and blades are easy to separate, so we must pay attention to maintenance.
(4) Insufficient antifreeze and too little coolant will also cause the water temperature to be too high, so it is necessary to add or replace the coolant in time. Due to the irregular addition and replacement of antifreeze, the engine water channel and water tank will be blocked in advance, resulting in excessive water temperature. Antifreeze should be replaced once every two years, and original fittings must be used when replacing and adding. If the concentration is too high, the heat dissipation effect will be poor and the engine will overheat. This harm is not obvious when the engine is running at low load, and the coolant temperature will be too high when it is running at high load and high speed. Therefore, it is not allowed to add antifreeze solution at will, and the concentration must be detected first. Different kinds of antifreeze cannot be mixed for use, so as not to cause chemical reaction, produce precipitation or bubbles, and reduce the use effect; When replacing antifreeze, start the engine first, then stop the engine and release the cleaning liquid. Add clean water to the cooling system, idle for 10 minute, then drain water, and repeat several times until clear water flows out of the waterway, and then add new antifreeze and water.
(5) There is air in the cooling system, which causes the cooling water not to circulate normally.
(6) The cylinder gasket is damaged, which causes the high temperature and high pressure gas in the cylinder to enter the cooling system, so that the water temperature quickly rises to boiling. A new cylinder liner must be replaced. The cylinder pads of the new two valves are made of steel plates. Generally, short-term high water temperature will not burn the cylinder gasket, but it will be damaged if it is not cooled for a long time. (3) The water pump is damaged or the transmission belt slips, resulting in poor water pump. The pump can't rotate normally to generate enough water pressure, which will also reduce the flow of cooling water. Because the circulating flow of cooling water exerts water pressure through the water pump, the water pressure cooled by the radiator enters the engine water jacket, forcing the cooling water that absorbs heat to flow to the radiator to dissipate heat. If the water pump does not work well, the water pressure is not high, the circulating flow of cooling water is reduced, and the heat dissipation effect is not obvious, resulting in high water temperature in the cooling system. The water pump is damaged, and the coolant can't be sent to the water tank, resulting in poor circulation of coolant and high water temperature until the pot is boiled. Need to repair or replace a new water pump. When replacing the timing belt, be sure to check the water pump for signs of leakage. If there is leakage, please replace it. Please carefully check one side of the timing belt for signs of water leakage. For vehicles with mileage exceeding1.2000 km, the owner is advised to replace the water pump when replacing the timing belt. For vehicles with long mileage, the shaft and blades are easy to separate, so we must pay attention to maintenance.
(4) Insufficient antifreeze and too little coolant will also cause the water temperature to be too high, so it is necessary to add or replace the coolant in time. Due to the irregular addition and replacement of antifreeze, the engine water channel and water tank will be blocked in advance, resulting in excessive water temperature. Antifreeze should be replaced once every two years, and original fittings must be used when replacing and adding. If the concentration is too high, the heat dissipation effect will be poor and the engine will overheat. This harm is not obvious when the engine is running at low load, and the coolant temperature will be too high when it is running at high load and high speed. Therefore, it is not allowed to add antifreeze solution at will, and the concentration must be detected first. Different kinds of antifreeze cannot be mixed for use, so as not to cause chemical reaction, produce precipitation or bubbles, and reduce the use effect; When replacing antifreeze, start the engine first, then stop the engine and release the cleaning liquid. Add clean water to the cooling system, idle for 10 minute, then drain water, and repeat several times until clear water flows out of the waterway, and then add new antifreeze and water.
(5) There is air in the cooling system, which causes the cooling water not to circulate normally.
(6) The cylinder gasket is damaged, which causes the high temperature and high pressure gas in the cylinder to enter the cooling system, so that the water temperature quickly rises to boiling. A new cylinder liner must be replaced. The cylinder pads of the new two valves are made of steel plates. Generally, short-term high water temperature will not burn the cylinder gasket, but it will be damaged if it is not cooled for a long time.