Whether installing clothes racks on the balcony of the bedroom or the balcony of the living room, many people will put clothes racks in the bedroom. Clothes racks can be placed on the balcony of the bedroom, next to the window and at the height in the bedroom, which can optimize the feng shui pattern in the home. The following is whether the clothes rack is installed on the bedroom balcony or the living room balcony.

Is the hanger installed on the bedroom balcony or the living room balcony? 1 Installation position of clothes rack.

At the top of the balcony to be installed, measure the diameter of the lighting lamp at the top of the balcony with a steel ruler, and then make installation marks on both sides of the lamp (the length depends on the size of the balcony). Then measure the distance between the mark and the balcony edge, and determine the installation width of the top seat according to this distance. Then measure the length of the balcony with the lamp as the center.

According to the length of the clothesline, it is determined that the two sides of the lamp are equally divided into 80 cm- 100 cm, and then there are four intersections at the interval of width measurement. These four intersections are the installation positions of the top seat of the clothes hanger. After the position is determined, drill holes with an electric drill, and then fix the four top seats with expansion screws (if the length of the rod exceeds the normal size, this interval will be adjusted accordingly).

How to install hangers

1. Open the outer package of the lifting hanger and check whether the parts of the hanger are intact. General spare parts include: corner device, fixing cover, lifting ring, hand crank, expansion screw, handle, wire rope, lifting lug and pulley frame.

2. First, install the hand crank, and install the hand crank at both ends of the corridor. Measure the position where the hand crank needs to be installed, which is generally 1.2 meters away from the ground. Place the handle in the position to be installed, then mark the hole position to be punched and fixed with a marker, then remove the handle, punch with an electric drill, install an expansion rubber plug, and fix and tighten the handle. Then shake out all the wire ropes in the crank. When shaking out the wire rope, it is necessary to pull the wire rope to avoid wire disorder until the handle rotates.

3. Determine the installation position of pulley frame. The pulley frame is the four supporting points installed on the ceiling. Double pulley frame is near the corner, and single pulley frame is at the end. Generally, taking a single pulley frame as an example, the distance between a single pulley frame and two side walls is more than 27 cm, while the distance between two single pulley frames is more than 45 cm, while the distance between a single pulley frame and a double pulley frame is generally 2M, but the final condition is the installation environment. Mark the installation position, mark the hole position, and then punch holes in the installation hole position.

4. After drilling, assemble the expansion screws with four pulley frames respectively.

5. After assembly, install two double pulley frames and two single pulley frames on the drilling hole respectively.

6. Assemble the corner device with expansion screws.

7, determine the installation position of the corner device, the position of the corner device must be perpendicular to the position of the hand crank, 90 degrees.

8. After determining the installation position, mark the hole and install the assembled corner device.

9. Thread the steel wire, disassemble the steel wire, hold one end of the two steel wires in it respectively, and thread them into the corner device first.

Install the fixing cover.

1 1. Install the lifting ring, cut off the four ends of the freshly ground steel wire, then pass through the lifting ring and tighten it.

12. Install the clothesline and fix the four rings on both sides of the two clotheslines.

How to choose a hanger?

1, look at the steel wire

Look at its thickness and elasticity. The thicker and softer the wire rope, the better. The identification method is to fold the wire rope in half and put it aside to see if it can be restored.

Step 2 look at the pulley

Pulleys are made of ordinary metals, even iron and copper. The product quality made of pure copper composite pulley is better, and moving pulley is more labor-saving.

3. Look at the thickness of the air drying rod.

Buying a hanger rod is not as thick as possible, but moderate. A pole that is too thick is too heavy to lift. The pole thickness should be moderate, and the thickness from 1.0 to 1.2mm is more suitable.

4. Look at the surface of the pole

The surface treatment of drying rod mainly includes polishing treatment, electroplating treatment, plastic spraying treatment and electrophoresis treatment. Electrophoresis treatment process is the most complicated, and the surface of the rod is very bright and graded. Polishing treatment is the simplest and belongs to low-end products. The surface of this rod looks bright, close to the primary color of aluminum alloy, but it has not been treated with any surface oxidation resistance. After a long time, the surface of the rod will turn black.

5. Look at the crank

The crank handle is the core component of the clothes hanger, which is very critical. When you buy it, you should turn the handle directly to see if it is smooth and the noise will be too loud.

6. Look at the expansion screw

Expansion screws are often ignored by consumers, which actually determines whether the product is easy to install and firm.

7, look at the drying rod material

At present, there are stainless steel, Al-Mg alloy and Si-Mg-Ti-Al alloy on the market. Consumers should distinguish between materials. First, pay attention to the description of the merchants and choose the merchants with good reputation. Second, pull both ends of the lever directly. Aluminum alloy bends easily and cannot be repaired, while titanium alloy does not.

Is the hanger installed on the bedroom balcony or the living room balcony? 2. hanger feng shui.

1, the principle of choosing clothes hangers

The selection of hangers should be based on the principle of simplicity and comfort to avoid grotesque shapes.

It is best to hang the clothes rack vertically to avoid rising.

The items hanging on the hanger should be neat and not messy.

Don't choose clothes hangers with too many splits, outward publicity and uneven levels.

Clothes hangers are generally not placed in the bedroom square, but should be placed in the corner.

Clothes hangers should not be placed at the end of the bed, but on both sides of the bed.

The color of the clothes hanger should be selected according to the birthday of the residents, and the orientation should avoid the southwest and northeast.

Step 2 avoid sharp corners

Furniture in the bedroom, including beds, wardrobes, dressing tables, clothes hangers, etc., should not be made of metal materials such as stainless steel, iron and aluminum. From the analysis of the attributes of the five elements, because gold is rigid, sharp, evil, offensive, harmful and fierce, their harm to sleeping people is intangible, but it does exist. It's best to use wood and soil as beds, because wood and soil are soft and won't hurt people. In southern China, beds are mostly made of wood, while in northern rural areas, brick kang is used. This kind of bed is soil, which is beneficial to people's sleep and health.

This hanger looks like rotten wood.

The clothes rack is like a dead tree. This kind of clothes hanger is like a dead tree, with branches and leaves cut off and no head. There is no anger in the house, which is not good for the relationship between husband and wife, and it is even worse for the body. Moreover, the horns are rising, and there are many pathogens that can hurt people. It's not good to put it in any direction, fierce. We'd better not use this kind of hanger.

Step 4 swing the hanger

The hanger swings at will. Although these clothes hangers have no knives or horns, they look patchy. But it looks like a white sail at a funeral. Near the bed where you slept, you formed an elephant buried in the grave, a fierce elephant. It's easy to have nightmares, what goes around comes around, and your health will definitely go wrong. No matter where you put it, it's fierce. The image of random rise, the cause is difficult and unfavorable.

5. Be careful with the clothes hanger on the wall.

It is best not to install clothes hangers on the wall. The clothes rack on the ground is really indecent and does not hinder the entry and exit of the coat rack.

6, the space can not be put down.

If the house is small, don't put floor hangers, and don't turn the room into a warehouse, which will affect the activity space. It is not advisable to put too much furniture in the home, which will cause congestion and is not conducive to people walking. According to the feng shui furniture at home, European furniture is not conducive to the development of family transportation. After placing furniture, you have to turn around when you walk, and your family fortune is not smooth.

7. Wooden hangers

The wooden shape of the clothes hanger is noble and elegant, simple and connotative. This kind of clothes rack is round, smooth and elegant, and it does not make public when it rises. This kind of clothes rack and the clothes rack hanging on it are the best choice at home.

8. Color of clothes hanger

The color of furniture must be neutral and avoid cool colors. Indoor furniture should be put with hangers according to other furniture, otherwise it will be lifeless. In addition, it should also match the color of interior decoration.

Is the hanger installed on the bedroom balcony or the living room balcony? 3 how to install the solid wood floor-standing drying rack?

1. Generally, solid wood floor hangers are chassis or tripods. When installing, be sure to put the bottom up first.

2. The tripod hanger should also be installed at the bottom first.

3. After installing the bottom, you can install the middle pole at the top in turn, and the middle pole is slightly smaller than the bottom.

There are generally two kinds of hooks in the middle. One is that the hook comes with wire, which can be screwed directly.

5. The other is to screw it on with a Phillips screwdriver.

6. When the middle one is installed, the upper one is slightly thinner in turn. When it is tightened, it is at the top. Generally, there are four screws on it, and some of them are hexagonal wrenches. Such general manufacturers are equipped, so hangers are installed.

7. When installing, be sure to tighten the chassis so that it won't shake, and tighten the top, otherwise hanging too many clothes will be unstable.