I think the easiest way is to use glue. When gluing, first of all, the base must be flat, firm and reliable.
Find the size that needs to be installed, do some treatment on the surface that needs some silica glass glue, scrape off the ash to expose the cement mortar at the predetermined place, and then use silica glass glue. (Try to find a few points with silicone glass glue) Find a horizontal line at the lower edge of the mirror and then nail two round nails, and then you can press it.
Note that the object needs to be fixed for 48 hours after pressing. Guaranteed to be solid. Hehe, thank you!
Question 2: How to fix the mirror on the bathroom wall? Generally, most purchased mirrors have mounting holes (at the four corners of the mirror) and mounting accessories.
. You can:
1. Hold the mirror in your hand and stick it on the wall at a suitable position.
2. Mark the position of the mounting hole with a marker.
3. Drill the hole with a gun drill (6mm in diameter).
4. Insert the expansion tube and lock it with screws.
Question 3: How to nail the mirror to the wall and put the mirror where it is needed? Draw four holes in the wall with a pencil, remove the mirror, punch four 6-point holes in the drawing place with an electric hammer, knock the 6-point plastic expansion tube into the eye, put the mirror away, and screw the stainless steel tapping screw on the eye with a cross screwdriver.
Question 4: How is the glass fixed on the wall? Simple ways to fix the glass on the cement wall are: using high-strength glass glue or drilling holes in four corners, self-tapping nails, decorative buttons and so on. You can also use double-sided tape with glass glue around it. It is suggested to embed glass frames or drill holes in the four corners of the glass and fix them with anchor bolts. The specific method is as follows:
1. nailing method: this method fixes the decorative glass mirror on the base of the wall (or cylinder or top surface) with screws. The specific steps are as follows:
Wall treatment Wall surface should be smooth, without bulging and unevenness. If the wall is smooth, it can be directly used for installation. Otherwise, cement mortar can be used (if a proper amount of moisture-proof powder can be added, the effect will be better), and then it can be scraped flat.
Row of holes and drilling each decorative glass mirror needs to drill four fixed holes, which should be evenly distributed and not too close to the mirror edge to prevent cracking. At present, the fixed decorative glass mirrors sold in the market have generally been drilled, and the amorphous glass mirrors can be drilled at professional processing points.
Put the installation position of the glass mirror on the wall, then put the decorative mirror on the corresponding position on the wall, mark the corresponding hole position on the wall through the hole on the glass mirror, take off the mirror, and punch holes in the marked position on the wall with an electric drill or hammer. The aperture should be determined according to the size of the selected screw, which is generally less than 3 mm of the diameter of the screw end.
In order to prevent the decorative glass mirror from being damaged by uneven base, a layer of buffer material should be added between the mirror and the wall. It is best to choose 2~3 mm thick thin felt or sponge board elastomer and fix it on the wall with white latex. The size of the gasket material is smaller than that of the glass 10~ 15 mm, so that the periphery can be sealed with caulking paste after the mirror is installed.
Before installing the glass mirror, a layer of kraft paper protective layer should be pasted on the back of the glass mirror. The specific method is to brush a layer of white latex on the back of the mirror, then stick a piece of kraft paper on the back of the mirror, and then scrape it flat with a plastic plate. Pre-embed plastic expansion bolts in the holes punched in the wall, align the mirror with the holes, fix them with screws and tighten them diagonally. It is suggested that the glass mirror should be stable and free from shaking.
After the glass around the enclosure is installed and fixed, in order to prevent moisture from invading the mirror back and affecting the service life and quality of the mirror, the gap between the mirror and the wall should be filled with caulking paste.
Second, paste method: paste the glass mirror directly on the wall base with adhesive with high bonding strength. This method is suitable for wall installation within 1 m2. If the size of the mirror is large, or the mirror is installed on the ceiling, it is best to use a combination of pasting and nailing to ensure that the mirror will not fall and hurt people when it is damaged. The specific pasting method is as follows: Note: See the supplementary section for another pasting method.
Clean the back of the mirror to remove dust and sand. Stick a layer of kraft paper on the back of the mirror as a protective layer.
Then apply all-purpose glue to the kraft paper on the back of the mirror and the base of the wall. Under the condition that the rubber surface does not stick to the hand, the glass mirror is directly attached to the wall according to the pre-played position line. Press the mirror by hand to make it close to the wall, and pay attention to the adhesion at the corners.
When pasting the mirror, seal the periphery with caulking paste.
It should be noted that the wall should be flat before sticking the mirror, otherwise it should be leveled with cement mortar. In addition, the all-purpose adhesive cannot be directly coated on the back of the mirror to prevent corrosion from damaging the coating of the mirror.
3. Embedding method: Embedding method uses stainless steel, aluminum alloy or wood wire as the frame of the glass mirror, fixes the frame with the wall base with nails, and then embeds the glass mirror in the frame. This method is suitable for the installation and fixation of large-area glass mirrors. The specific embedding method is as follows: Note: See the supplementary section for another embedding method.
Firstly, according to the size of the border bead, line, row holes and punch holes. According to the played line, first fix the batten of the lower frame with the nail spacing of 10~ 15 cm, so as to increase the supporting strength at the bottom.
Then glue the blanket to the base with white latex. Then the mirror is embedded in the battens of the lower frame, aligned with the wall, and the battens of the upper frame and the battens on both sides are installed. It should be noted that when fixing wood battens, it is best to use a nail gun of 20~25mm to avoid using ordinary round nails to prevent the mirror from being broken when nailing wood battens.
supplement
Stick with double-sided adhesive: In addition to all-purpose adhesive, you can also stick the mirror with double-sided adhesive. This kind of double-sided adhesive tape is coated on both sides of the sponge board with high-strength adhesive, with a thickness of about 2~3 mm and a certain elasticity. When in use, it is cut into strips with a width of 5- 10 cm, and the protective paper on one side is torn off first. & gt
Question 5: How is the mirror fixed on the wall? Generally, most purchased mirrors have mounting holes (at the four corners of the mirror) and mounting accessories.
. You can:
1. Hold the mirror in your hand and stick it on the wall at a suitable position.
2. Mark the position of the mounting hole with a marker.
3. Drill the hole with a gun drill (6mm in diameter).
4. Insert the expansion tube and lock it with screws.
Question 6: Please tell me how to fix the mirror on the wall.
If it is a finished mirror with a nail hole at the back, nail two screws on the wall and hang them;
If you draw your own mirror, and the back is flat, you can stick it with double-sided foam.
Question 7: How can I stick the mirror on the wall? Small ones can be decorated with that kind of foam double-sided tape, which is very strong. Drill when you are big. This is impossible without special tools!
Question 8: How to install the mirror on the wall? First, a small area of glue can be used, but the bottom surface should be clean and not greasy.
Second, the area is slightly larger, and the bolt can be locked by drilling holes in the glass;
Three, the area is larger, can use dry hanging form:
Wall tension test-installation keel (wooden keel, steel keel)-special fastener.