management mode
Pettis uses online to offline, that is, the combination of online and offline, which is convenient for consumers to measure product performance. Online, through the construction of online shopping malls, various promotional activities and prepayments, there is a product experience hall offline, and consumers can go to physical stores to experience the product effect personally. In this process, Pettis provides online customer service and cargo adjustment support at any time. After fully experiencing the performance of the product to be purchased, the user confirms the payment, and the merchant collects the payment and delivers the goods. This model is more offline, more conducive to consumers, so that consumers can truly appreciate the practicality of consumption.
main products
Pettis products are mainly shower rooms, including simple shower rooms and shower room partitions.
Business philosophy
Because it is single-minded, it is more focused; Because of concentration, it is more professional.
Future prospects
Pettis is a dark horse in the domestic bathroom industry, and its business model has greatly improved the user experience and facilitated consumers' purchase.
product mix
A, structural technology:
Pettis's six structural technologies are reasonable, and the humanized interactive design makes the complicated life simple.
1. The new waterproof technology adopts a new type of backflow water stop at the bottom of the door to avoid the outflow of water droplets and truly separate wet from dry.
2. The installation of automatic adjustment technology adopts bilateral design and internal adjustment, which is easy to correct construction errors.
3. Damping and silencing technology makes sliding smoother and ultra-silent.
4. Hinge screw hiding technology: All hardware parts are equipped with invisible cover plates, and even the wall structure is hidden, which ensures the functionality and makes the products more fashionable and beautiful.
5. "Spiral" guide rail structure technology: the lower guide rail has no U-shaped groove, and there is no dust and sewage during use, which is easy to clean.
6. Stone embedded guide rail technology: it integrates water retaining and sliding, which is more convenient and better sealed.
Second, the materials and accessories
1. Pettis hardware is made of 304 stainless steel.
2. Handle: made of 304 stainless steel, the supporting part is strong enough, not easy to wear, full of toughness, no burr at the joint, smooth and flat, reasonable in design, and convenient for sliding the door.
3. Ultra-smooth mute technology: the sliding effect is second to none in the industry, smoother and ultra-mute.
4. Automatic rebound structure technology: ensure that the guide wheel is always close to the glass, seamlessly combined, stable and smooth.
(upgraded to high zinc alloy pulley)
4. Pulley: After 20,000 rolling wear experiments, the mobility and stability of the movement are ensured.
5. Built-in outer wheel structure technology: beautiful and generous, reducing pulley wear. And greatly prolongs the service life of the pulley.
6. Super-large load-bearing technology: adopt the latest lower pulley mode, with heavy load, small width limit, smooth and silent sliding, and the upper guide rail will never bend.
Thirdly, salt spray test.
Corrosion refers to the damage or deterioration caused by the environment. Salt spray corrosion is the most common and destructive atmospheric corrosion. Salt spray corrosion on the surface of metal materials is caused by chloride ions penetrating through the oxide layer and protective layer on the surface of metal and electrochemical reaction with internal metal. Chlorine ion replaces oxygen in the oxide layer, which turns insoluble compounds into soluble chlorides and passive surfaces into active surfaces, causing extremely bad adverse reactions to products.
Traditional merchants basically adopt neutral salt spray test (NSS test), using 5% sodium chloride salt solution, and the PH value of the solution is adjusted in the neutral range (6 ~ 7) as spray liquid. The test temperature is 35℃, and the salt spray sedimentation rate is required to be between1~ 2ml/2000px2.h. ..
Pettis shower room adopts the latest copper salt accelerated acetic acid salt spray test (CASS test), the test temperature is 50℃, and a small amount of copper salt-copper chloride is added to the salt solution, which strongly induces corrosion. Its corrosion rate is about 8 times that of NSS test.
Product advantage
Smooth sliding, silent, and the upper guide rail will never bend.
salt spray test
Corrosion refers to the damage or deterioration caused by the environment. Salt spray corrosion is the most common and destructive atmospheric corrosion. Salt spray corrosion on the surface of metal materials is caused by chloride ions penetrating through the oxide layer and protective layer on the surface of metal and electrochemical reaction with internal metal. Chlorine ion replaces oxygen in the oxide layer, which turns insoluble compounds into soluble chlorides and passive surfaces into active surfaces, causing extremely bad adverse reactions to products.
Traditional merchants basically adopt neutral salt spray test (NSS test), using 5% sodium chloride salt solution, and the PH value of the solution is adjusted in the neutral range (6 ~ 7) as spray liquid. The test temperature is 35℃, and the salt spray sedimentation rate is required to be between1~ 2ml/2000px2.h. ..
Pettis used the latest copper salt to accelerate acetic acid salt spray test (CASS test), the test temperature was 50℃, and a small amount of copper salt-copper chloride was added to the salt solution, which strongly induced corrosion. Its corrosion rate is about 8 times that of NSS test.
Shower room partition
Product characteristics
Float toughened glass PK ordinary toughened glass
Pettis toughened glass
The area safety crushing capacity of 1 and 50X50MM reaches 60-80 grains (more than 40 grains in the national standard).
2. Float tempering process,
3, the tempering flatness is high,
4. The glass surface is smooth, and the convexity and concavity are only 1% of that of ordinary tempered glass.
5, do not hang dirt, easy to clean, glass no atomization phenomenon.
Ordinary tempered glass: ordinary workshop tempered,
1, there are bubbles and tiny particles in the glass,
2. Uneven stress, surface stress leads to self-explosion.
3. There are tiny bumps on the surface, which will cause dirt to stay and make it difficult to clean, and lead to glass atomization and even yellowing.
product mix
1. The new waterproof technology adopts a new type of backflow water stop at the bottom of the door to avoid the outflow of water droplets and truly separate wet from dry.
2. The installation of automatic adjustment technology adopts bilateral design, and the internal horizontal and vertical adjustment can effectively correct the construction error during installation. It effectively solves the problems that cement workers can't correct the deviation because they don't have the function of front, back, left and right adjustment, the installation effect of shower room is not good, the glass is easy to explode when it is twisted laterally, and the pulley is easy to wear.
3. Damping noise elimination technology
Sliding is smoother and ultra-silent.
4. Hinge screw hiding technology All hardware parts are equipped with hidden cover plates, and even the wall structure is hidden, which ensures the functionality and makes the products more fashionable and beautiful.
5. The structure technology of "spiral" guide rail, the lower guide rail has no U-shaped groove, and it is easy to clean without dust and sewage during use.
6. Pulley technology
Pulley is the most important thing to ensure the quality of shower space. Pettis pays attention to intelligent design, high matching accuracy and long service life. All pulleys are made of imported stainless steel bearings, which have been successfully opened for more than 20,000 times. Unique plastic alloy double pulley design, successfully opened more than 20 thousand times for normal use. In order to make the products achieve the best use effect, Pettis has built a pulley structure for each product according to its structure:
1) Super smooth mute technology Four-track eight-wheel drive, smoother and super mute.
2) Super-load technology adopts the latest pulley lowering mode, which has large load-bearing capacity, small product width limit, smooth and silent sliding, and the upper guide rail will never bend.
3) Built-in external sliding structure technology effectively reduces pulley wear and greatly prolongs pulley service life.
4) The bouncing three-pulley structure technology is convenient to install, effectively prevents derailment, and is safe and stable.
5) Automatic rebound structure technology ensures that the guide wheel is always close to the glass, seamlessly combined, stable and smooth.
7.hinge
The spring is thicker and firmer, and the switch is more stable: double-layer electroplating, anti-corrosion, anti-electroplating, and more beautiful.
Selected Great Wall 304 Stainless Steel:
The density of SUS304 stainless steel containing 8% nickel is 7.93g/cm3.
Real SUS304 international brand 1Cr 18Ni9
Pettis uses a thickness of 0.8 mm.
Great Wall 304 stainless steel has strong toughness, heavy pressure resistance and long service life.