There may be something wrong with your hard disk. Is the hard disk indicator always on?

Why does my computer often get stuck?

..... "Hello:

Please give due consideration to the following aspects:

1, kill viruses and clean up redundant plug-ins;

2. Use some software to optimize system services and clean up disk junk files;

3, uninstall redundant software, those software that is not used once every n years will be uninstalled;

4. When the system starts, try to run programs automatically as little as possible, except for the input method ctfmon.exe and antivirus software.

5. Check whether there is anything wrong with drive C (right-click drive C-Properties-Tools-Start check, check Auto Repair, and check when restarting);

6. Defragment disk C (right-click disk C-Properties-Tools-Defragment);

7. Use the system theme without any special effects, turn off the desktop background and minimize the icons and files on the desktop; 8. Specify the IP address, gateway and DNS manually. Used for local connection;

9. Control Panel-Internet Options: Advanced-Restore advanced settings and reset;

0, clean up the dust, and then check whether the memory stick, hard disk and other equipment are firmly inserted; Or swap memory slots;

..... "If these are not enough, then you need to start working hard:

A, uninstall antivirus software, secure memory resident software, etc. (This may lead to poisoning);

B, completely install the operating system;

C, purchase a large-capacity memory matched with the motherboard;

D, change the operating system and use WindowsXP.

..... "If I can help you solve it, please feel free to adopt it;

My computer is always stuck. How to solve it?

3. Disable hibernation

Specific closing method:

Open the control panel and double-click power management.

Select the Hibernation tab in the Power Management Properties dialog box.

Uncheck the Enable Hibernation check box and click the OK button.

Once the Enable Hibernation check box is cleared, Windows XP will automatically delete the Hiberfil.sy file from your hard disk.

Hiberfil.sys saves all the information in the memory to hiberfil.sys when the system sleeps, and its size is always the same as your physical memory. To delete this file, you can open the power management under the control panel, select the hibernation option, and remove the check before "Enable hibernation", and the hiberfil.sys file will be automatically cleared. Hiberfil.sys file may be very large, which is a special system file that Disk Defragmenter can't organize. Therefore, the existence of the file Hiberfil.sys will prevent the disk defragmenter from completely defragmenting.

4. Virtual memory settings

Under normal circumstances, windows XP uses the remaining space of drive C as virtual memory by default. Therefore, the larger the remaining space of drive C, the better it will run on the system. Virtual memory changes dynamically with your use, so disk fragmentation is easy to occur on disk C, which affects the running speed of the system. Therefore, it is best to set the virtual memory in other partitions, such as drive D. Check the virtual memory settings as follows:

Right-click My Computer, left-click Properties, click the Advanced tab, click the Settings button in Performance, then select the Advanced tab, and click the Change button below to open the virtual memory settings window. Generally, the default virtual memory is a range of values from small to large, that is, the range of virtual memory changes. The specific value depends on the size of your physical memory, which is generally 0.5 to 2 times that of 65438+ physical memory. If the memory is 256M, you should set 256* 1.5=384M, or just 5 12M. The setting method is as follows:

Assuming that the memory is 256M and the virtual memory is placed on drive D, clear the default first, keep drive C selected, select "No paging file (n)" and press the "Set" button, and the virtual memory next to drive C will disappear. Then select drive D, select User-defined Size, and add 50 in the Initial Size and Maximum Value boxes below. You will see the words "5 12-5 12" next to disk D, indicating that it is set up, and then confirm it all the way. Finally, the system must be restarted to complete the setup.

Note: there can only be one virtual memory, only on one disk!

Virtual memory setting: the virtual memory below 5 12M should be set to 2-3 times; 5 12M is set to 1.

What is the reason why computers are always stuck, and what can be done to solve it?

Computer Card It is recommended to check the computer:

1, network

Check the network, is the network speed bad? Open Tencent Computer Manager's toolbox and test the network speed to see if the network speed is not very good.

There is too much dust on the computer host.

The host itself will absorb dust. If it is not cleaned for a long time, the fan will be stuck and the heat dissipation will not be good. You can clean it with a hair dryer.

There is too much computer rubbish.

Long-term use of computers will lead to excessive garbage, which will lead to computer cards. You can use the garbage cleaning function of Tencent Computer Manager to clean up the garbage. Tencent computer housekeeper will clean up the garbage and scan it.

This computer runs too much software.

Open Tencent Computer Manager to speed up one-click optimization and optimize some unnecessary startup software.

5, in the virus, Trojan horse

It will also cause the computer to be too slow. You can turn on the red umbrella killing engine of Tencent Computer Manager (turn on Tencent Computer Manager to kill viruses, scan and kill). If you kill a Trojan or virus, you should restart it immediately. After restarting the computer, you will go to "Quarantine | Recovery" and completely delete the Trojan and virus!

I hope my answer can help you. If not, please forgive me

What is the main reason of computer jam and how to solve it?

First, clean the disk and defragment it.

1. In my computer window, right-click the drive letter to be cleaned-Properties-Clean Disk-check the file to be deleted-OK-Yes.

2. Clear the temporary files, and then start-run-enter% temp%-OK. 3. Clean registry and junk files with optimizer or super rabbit.

4. Close some startup programs and start-run -msconfig- start. In addition to antivirus software and input method, general programs can be closed.

5. Delete the unused program software.

6. Defragmentation-Start-All Programs-Accessories-System Tools-Defragmenter-Select C- Analysis-Defragmenter.

Second, optimize your computer with an optimizer or a super rabbit, and then choose the following methods for re-optimization.

1. Disable idle IDE channels.

Right-click My Computer-Properties, then click Hardware and then click Device Manager to open the IDE ATA/PATA Controller, then enter the primary and secondary IDE channels respectively, select Advanced Settings, and find an item whose current transmission mode is not applicable here, and set the device type of this item to None.

2. Optimize visual effects

Right-click my computer-Properties-Advanced, and in the performance column, click Settings-Visual effects to adjust to the best performance, or just keep some necessary items.

3, startup and fault recovery

Click "Settings" in "My Computer"-"Properties"-"Advanced"-"Startup and Troubleshooting", and remove the options of "Write events to system log", "Send management alarm" and "Auto-restart"; Set "Write Debugging Information" to "None"; Click "Edit", and in the notepad file that pops up:

[Operating System] Timeout =30 Change 30 seconds to 0 seconds.

4. Disable error reporting

"My Computer"-"Properties"-"Advanced"-Click "Error Report", click "Disable Error Report", and check "Notify me when a serious error occurs"-OK.

5. Set up System Restore

Click Start-All Programs-Accessories-System Tools-System Restore. In the system restore interface, uncheck "Turn off system engineering restore on all drives". In the Available Drives area, select the partition where the system disk is located, and click Settings to enter the System Restore Settings window.

6. Turn off automatic updates

To turn off automatic updates, right-click My Computer-Properties-Automatic Updates, and then select Turn off automatic updates in the notification settings column. Check "I will update my computer manually".

7, close the remote desktop

Right-click My Computer-Properties-Remote, and uncheck "Allow users to connect to this computer remotely" in the remote desktop.

8. Disable the hibernation function.

Click Start-Control Panel-Power Management-Hibernation, and uncheck the box before "Enable Hibernation".

9. Turn off the "Internet Time Synchronization" function

Click Start-Control Panel-Date, Time, Language and Regional Options, and then click Internet Time to uncheck "Automatically synchronize with Internet time service".

10, turn off disk indexing.

Open my computer, right-click the drive, select "Properties", and uncheck "Use index to find files quickly".

1 1. Disable redundant service components.

Right-click My Computer-Administration-Services and Applications-Services, and set unnecessary services as disabled or manual in the right pane.

12, close Dr. Watson, Dr. Watson.

Click Start-Run-Enter ... >>

Why did the computer suddenly get stuck? What should I do?

No matter how good the configuration is, you may suddenly find that the computer is stuck one day-open a program? Wait half a day; Playing games? No more playing ... Are you poisoned? I didn't check it carefully. Why? Please have a look at my article, which may inspire you. First, the CPU is overloaded or not working properly. Check the cooling, dust removal and oiling of CPU and graphics card, or replace the fan. Second, the power supply voltage is unstable and the power supply is insufficient. Replace high-quality and high-power power supply. Third, always clean up the disk and defragment it. 1. In the My Computer window, right-click the drive letter to be cleaned-Properties-Clean Disk-Check the files to be deleted-OK-Yes. 2. Clear the temporary files, and then start-run-enter "%temp%"-OK. 3. Clean registry and junk files with optimizer or super rabbit. 4. Close some startup programs and start-run -msconfig- start. In addition to antivirus software and input method, general programs can be closed. 5. Delete the unused program software. 6. Defragmentation-Start-All Programs-Accessories-System Tools-Defragmenter-Selected Disks-Analysis-Defragmenter. 7, reduce the memory burden, open the program should not be too much. If you open too many documents or run too many programs at the same time, you won't have enough memory to run other programs. Close unused programs and windows at any time. Fourth, upgrade the graphics card and network card driver, and change to a higher-end graphics card. Fifth, increase physical memory. Sixth, set up virtual memory reasonably. 1, to play games, the virtual memory can be set larger, and the maximum and minimum values can be set to 2-3 times of the physical memory. If it is large, it will take up too much hard disk space. 2. The method of setting virtual memory is: right-click my computer-Properties-Advanced-Performance Settings-Advanced-Virtual memory change-select the partition for storing virtual memory (page file) in the drive list-customize the size-set the values in the initial size and maximum value, then click the "Settings" button, and finally click "Settings". 3, virtual memory (page file) storage partition, must have enough space, hard disk resources are insufficient, resulting in insufficient virtual memory, in a computer, it is enough to set up virtual memory in one partition, not in multiple partitions. Seven, use optimization master or super rabbit to optimize the computer. All these methods have been used, and the computer is still a card. You have to check whether there is something wrong with your hardware, or try to change a system.

Why does my computer always run one card at a time?

I'll tell you in simple and complicated ways, which may be useful and can pass the psychological counselor's test.

Simple edition

First, the cause of the virus.

Second, the hardware problem. Such as power supply

Third, the problem of software. Such as CPU temperature monitoring software.

Four, the system file is lost, caused by misoperation.

5. Hackers attack you.

The specific solution is to redo the system. 1, 3, 4 and 5 can be excluded. If it still crashes or gets stuck, it's a hardware problem.

Professional edition

Hardware reason: ※:

"Poor heat dissipation": monitors, power supplies and CPU will generate a lot of heat when working, so good ventilation is very important. If the monitor is overheated, it will lead to color and image distortion and shorten the life of the monitor. Working too long will also lead to poor heat dissipation of power supply or monitor, leading to computer crash. The heat dissipation of CPU is an important issue related to the stability of computer operation, and it is also the "hardest hit" where heat dissipation failures occur.

"Dust Black Boy": Too much dust in the machine can also lead to a crash. If the floppy disk drive head or the laser head of the CD-ROM drive is contaminated with too much dust, it will lead to reading and writing errors, which will seriously cause the computer to crash.

"Software and hardware are incompatible": For example, 3D production and some special software may not be installed or started normally on some computers, and there may be problems with software and hardware compatibility.

"Memory failure": mainly caused by loose memory and self-quality. The corner fault of memory stick should be eliminated according to the specific situation. If there is a problem with the quality of the memory, the memory needs to be replaced to solve the problem.

"Hard disk failure": Bad tracks and bad sectors are mainly caused by aging or improper use of hard disks. This makes it easy for the machine to collide when moving. Special tools and software can be used for troubleshooting. If the damage is serious, only the hard disk can be replaced. In addition, for motherboards that do not support UDMA66/ 100, we should pay attention to the setting of hard disk operation mode in CMOS.

"CPU overclocking": overclocking improves the working frequency of CPU, and may also make its performance unstable. The solution, of course, is also relatively simple, that is, let the CPU return to normal frequency.

"Hardware resource conflict": It is common that the settings of sound card or video card conflict, resulting in abnormal errors. In addition, if other devices interrupt, DMA or port conflict, a few drivers may be abnormal, leading to crash. The solution is to start in "Safe Mode" and in "Control Panel"->; "system"->; Make appropriate adjustments in "Equipment Management".

"Inferior parts": A few unscrupulous businessmen use inferior boards and memory when assembling machines for customers, and some even sell fake motherboards and polished CPU and memory chips. This kind of machine is unstable and will inevitably crash. Therefore, users should be vigilant when purchasing machines.

Software reason: ※:

Virus infection: The virus will reduce the working efficiency of the computer sharply, resulting in frequent crashes. This kind of fault can be detected by running antivirus software, which should be upgraded in time.

Incorrect CMOS settings: The computer can't be started due to incorrect hard disk parameter setting, mode setting and memory parameter setting.

Deleting system files by mistake: Because Windows 9X needs mand, Io.sys, Msdos.sys and other files to start, if these files are deleted by mistake, even if all kinds of hardware in CMOS are set correctly, it will not help. At this time, you need to restart the system with the system disk, and then transfer the system files again.

Initialization file corruption: Because Windows 9X needs to read System.ini, Win.ini and registry files, if there are Config.sys and Autoexec.bat files, these two files will also be read. As long as these files have error information, they may crash, especially the four files of System.ini, Win.ini, User.dat and System.dat are particularly important.

Lost dynamic link library file (DLL): Another file is also very important in Windows operating system, that is, DLL file with extension, which is essentially a * * * exclusive file. If a * * * file is deleted when deleting an application, especially the more important core link file, the system will ... >>

The computer has been used for a long time, but it is still stuck after frequent cleaning. What should I do? 10.

There are many reasons for computer cards, one of which is that the garbage in the computer takes up memory. Cleaning up garbage can be solved, and the following aspects can be considered;

1, computer poisoning is the main reason for computer jam;

The solution is to install a better antivirus software, such as Tencent Computer Manager, Norton, Kaspersky and so on.

2, there are too many running software and residual system garbage in the computer, and the cpu can't run.

Solutions; Install a security management software, delete the unused software, clean up the system garbage in the computer, and save time, such as Tencent Computer Manager, Kingsoft Guardian, Baidu Computer Manager and so on. 3, it is the problem of computer accessories, such as cpu overheating, computer card, small memory, computer card, hard disk aging and so on.

The solution is to properly replace the accessories in the computer, such as memory chips, cpu and so on.

4, the computer's memory is too small, you can appropriately increase the computer's memory.

Where is the computer card? I couldn't get through.

Don't worry, there are probably the following reasons why computers often get stuck. You can refer to them.

1. The computer inadvertently installed malicious software, or generated malicious programs when surfing the Internet, all of which were caused by the computer being infected with a virus. It can be repaired by Tencent computer housekeeper. The method is simple. Download the computer manager-open it-kill virus-lightning kill/comprehensive kill, or open the computer manager-toolbox-stubborn Trojan bane-clean it up.

2. The memory stick in the computer case is dusty. Take it out, wipe it clean and put it back. 3. Junk files piled up in the computer, temporary files when browsing web pages and downloading programs will occupy the computer memory, which will lead to excessive CPU load and temperature rise, leading to blue screen and crash. This problem can also be fixed by computer housekeeper. Open the computer housekeeper-clean up the garbage-check the folder that needs to be cleaned-clean it with one click.

4. If the computer downloads too many running programs, it will also occupy a lot of memory, resulting in a card machine. You can open Computer Manager-Software Management-Software Uninstall-Delete.

Is it because the computer has been used for a long time that I can only try to reinstall the system?

I hope my answer can help you ~

Why are computers always one card at a time?

To solve the problem of computer card, it is necessary to optimize the performance of the system and software. Then properly maintain the hardware. The following is for reference only.

1 360 Many functions of security guards can be used, which can solve many problems:

① Regularly clean up the garbage and redundant information in the registry;

② Use its optimization function to optimize the system and reduce startup projects;

③ Slimming the system disk and registry.

2. The highlight of 2.windows Cleaning Assistant is to clean up bad plug-ins, but its "fault repair" function is very powerful.

3. The highlight of the malware cleaning assistant is to clean up malicious programs.

4. Insist on cleaning up disk fragments once a month; 5. Check the installation of disk C and game software. Methods: Right-click the keyboard symbol->; Attribute-> Tools-> Start checking->; Select the check boxes "Automatically repair file system errors" and "Scan and try to repair bad sectors"->; Start-> Automatic restart-> Wait patiently for a few minutes.

6. Use the driver wizard to check the hardware status of the computer to see if there are incompatible and mismatched drivers.

Note: You can only upgrade if it prompts for an upgrade driver. For drivers that don't prompt for upgrade, don't blindly specify upgrade! If it is an old machine, don't use this software!

7. Clean the CPU fan and radiator dust. If necessary, apply a layer of thermal conductive silica gel on the contact surface between the radiator and CPU.

8, memory stick * * *, use the eraser to wipe the gold finger and put it back.

Each of the above operations can speed up the operation of the computer.

Your memory is still the second generation, only 2G, so it's strange if you don't get stuck. . .